Friedrich ZoneAire Compact single-hose portable AC with heat (P08SA / P10SA / P12SA): quick sheet

Covers: Friedrich ZoneAire Compact single-hose portable air conditioners with heat: P08SA, P10SA and P12SA (115 V, 15 A circuit, NEMA 5-15P plug), R-410A per the manual. The two digits appear to give the capacity class (08, 10, 12); confirm BTU/h on the rating label. Heating is done by reversing the hot and cold air outlets and feeding the hose out the window, per Friedrich. Other ZoneAire portables (dual-hose and the earlier P08S/P10S of 2015) have their own manuals. Search terms: P10SA, P12SA, Friedrich portable E4, ZoneAire Compact E1.

Single sourceBrands: Friedrich5 components

A single-hose portable that evaporates condensate through the exhaust in cooling, with a small water plate (tank) that stops the unit with E4 when full. In heat and dehumidify modes Friedrich says to pull the drain cap and run a drain hose. Codes are few (E1, E2 sensor shorts, E4 water full); most calls are tank, hose and filter.

Safety first

Disconnect power before servicing or cleaning (Friedrich).
Do not over-extend or add extensions to the exhaust hose.
Refrigerant work is blocked: EPA 608-certified technician.

How it works

Cooling: condensate is evaporated and carried out through the exhaust hose; the drain cap must stay locked on the drain hole while cooling.

Heating and dehumidify: remove the drain cap and fit a drain hose; for dehumidify Friedrich says to remove the exhaust hose and drain to the outside.

Start delays: in cooling the compressor starts after the cooling indicator flashes for 3 minutes; in heating the heating indicator flashes for 3.5 minutes before compressor and fan start.

A thermal cut-off device protects the unit; blocked intakes or direct sun can make it shut down.

Components & tests

Unlock all 5 components, specs, service mode and teardown

Full library + AI assistant + the OnCall Tech app for iPhone & Android. $34.90, one time.

Get lifetime access

Official manufacturer documentation

Always confirm values against the tech sheet for the exact model.

OnCall Tech is a reference tool for trained technicians and can make mistakes. Always disconnect power and confirm with the manufacturer's documentation before you work. © 2026 OnCall Tech. Original content; not a reproduction of any manufacturer document.Generic part photos (not of this brand): Main electrical panel beside a subpanel with its cover removed by Gvolk, CC BY-SA 3.0

Diagnostic guides for this appliance

Guide · Air Conditioner

PTAC not cooling (fan runs, air not cold)

Most PTAC no-cool calls are airflow (filter, coils), a wrong control setting or a failed compressor start component. Rule those out before suspecting the sealed system.

6 steps ~60 minmoderate

Guide · Air Conditioner

PTAC not heating (electric heat or heat pump)

PTACs heat with electric strip heat, a heat pump, or both. Heat pump models switch to strip heat in cold weather. Check settings, then the heater element and its limits, then the reversing valve.

5 steps ~60 minmoderate

Guide · Air Conditioner

PTAC error codes: how to read and clear them

Most PTAC brands store fault codes that can be shown with a button combination on the control (for example, on GE Zoneline (2019 technical service guide) you hold FAN and the red AUX button together while the unit is OFF, and AUX clears stored faults; other models use other sequences, so use the model's tech sheet). Read the active code, fix the cause, then clear it.

4 steps ~20 mineasy

Other air conditioners manuals

Manual · Air Conditioner

Carrier Infinity Greenspeed 24VNA6 air conditioner and 25VNA4 heat pump (variable speed): quick sheet

Carrier Infinity Greenspeed Intelligence variable-speed outdoor units: 24VNA6 air conditioner (up to 26 SEER) and 25VNA4 heat pump (up to 24 SEER, up to 13 HSPF), 2-5 ton. Nomenclature from the service manual: 24 = AC, 25 = HP; V = variable speed; N = Infinity series; A = Puron (R-410A); 6 / 4 = SEER tier; two digits = nominal capacity (e.g. 36 = 36,000 BTU/h); voltage digit 3 = 208/230-1; compressor ID 4 = variable-speed scroll, 5 = variable-speed rotary. Serial format: week + year + plant letter + sequence (e.g. 0118E00001). Other 24VNA families (24VNA0, 24VNA9) use different software and code lists.

5 components4 common failuresCarrier

Manual · Air Conditioner

Trane XV20i / XV18 variable-speed outdoor units (4TTV0 AC, 4TWV0 heat pump, ComfortLink II): quick sheet

Trane variable-speed TruComfort / ComfortLink II communicating outdoor units: 4TTV0 air conditioners (XV20i family, e.g. 4TTV0024A1000C, 4TTV0036, 4TTV0048, 4TTV0060, 4TTV0061) and 4TWV0 heat pumps (Service Facts 4T-V0-SF). They use an Integrated Variable Speed Control (IVSC) board and a Communicating Display Assembly (CDA) in the outdoor unit. Distributor listings note several 4TTV0 revisions; confirm the full model on the nameplate before ordering parts. Single-stage XR14/XR16 units are on a separate sheet.

4 components3 common failuresTrane

Manual · Air Conditioner

Lennox XC21 air conditioner and XP21 heat pump (Dave Lennox Signature, iComfort-enabled): quick sheet

Lennox XC21 (air conditioner, service literature Corp. 1007-L2) and XP21 (heat pump, Corp. 1031-L7), 2, 3, 4 and 5 ton, R-410A, expansion valve indoor coils only. Both use an A175 main control (outdoor control part number 101798-xx) that works in communicating (iComfort) or conventional 24 V mode, plus a separate fan motor control. The XP21 literature describes a two-stage scroll compressor; the 2018 XC21 literature describes the compressor as one-stage while the same control section covers two-stage units, so confirm staging on the nameplate. For ML14XC1/EL16XC1 single-stage units see the separate sheet.

4 components3 common failuresLennox